Skip to main content

Bathroom Remodel - Demolition

I have been busy on the weekends since last week. I've spent four weekend afternoons so far to gut everything there is in one of the bathrooms except for the Windows. I still need a couple more afternoons to finish up the stripping and doing minor repairs (water-damaged floor board, etc).

The house was build in around 1954 or so. There were two unexpected challenges while demo'ing the bathroom. One was that the three sides of wall underneath the bathtub tiles were about 3-inch thick motor + cement with chicken wire. The other surprise was that the bathtub itself weighed tons, because it was made of galvanized steel (or steel).

I posted some photos showing the wall demo and the bathtub removal. The bathtub was so heavy like at least 250 pounds, I had to use an angle grinder with metal blade to cut it into four manageable pieces. Yes, that was a lot of work, too. It was smart thing to protect myself with 3M respirator, ear plugs and a pair of eye goggles.


This photo was taken after all tiles and the walls underneath the tiles were removed. Previous owner used chicken-wire mesh and 3-inch mortar and cement before adding tiles. I had to strip all tiles first and then use a hammer drill to break apart the cement wall inch by inch literally. The Makita hammer drill broke down so I had to get another hammer drill to finish tearing down the cement wall. All the debris were put into 12 contractor-grade trash bags. I think the total weight was no less than 500 lbs. This was really a lot of cement and mortar for one bathtub's walls.



After removing cement and mortar debris, I was able to wiggle and move the bathtub finally. Of course, I did detach the drain pipes first before moving the bathtub.

The bathtub was over 250 lbs at least. It was made of steel or galvanized steel. I decided to use an angle grinder with metal blade to cut it into four manageable pieces.


On the bottom of the bathtub, there were engravings showing the manufacturer and the city, date and serial number of the bathtub. It was made on 11/25/1958 in Richmond. I suppose it is Richmond, California. Wow, this steel bathtub has been in existence for 60 years!



I spent another hour to finish cutting up the steel bathtub into four pieces. Each piece weights about 70 lbs... much heavier than the standard 45-lb bench press weight.

Comments

  1. wow wonderful post..I am very much interested in this kind of blogs.this is truly helpful. Thank you so much for this interesting blog. demolition service

    ReplyDelete
  2. I read your post and this blog is very good. You have good knowledge on this. This post really impressed me. Thank you for sharing your knowledge with all of us. solid surface countertops

    ReplyDelete
  3. I am thankful to you for this article because you are providing such good information as I see, thanks for this.facebook marketing Altona

    ReplyDelete
  4. You have shared a nice article here. Your article is very informative and useful. engineering companies in south florida

    ReplyDelete
  5. Tearing down concrete structures or building is often time-consuming and expensive. Hydrodemolition is a demolishing technique that utilizes high pressure water jet equipment to remove deteriorated concrete in an efficient way. Thank you for sharing this remodelling work.

    ReplyDelete
  6. Impressive and powerful suggestion by the author of this blog are really helpful to me. drywall installation ottawa

    ReplyDelete
  7. The data you've supplied is quite beneficial. It's really instructive because it contains some of the most useful data about Bathroom Remodeling Inverness. Thank you for providing that information.

    ReplyDelete
  8. The information you've provided here is fantastic because it provides a wealth of information that is really useful to me. Thank you for sharing about miami interior designers in this blog.

    ReplyDelete
  9. It is truly a well-researched content and excellent wording. I got so engaged in this material that I couldn’t wait to read. Read more info about frameless bifold shower door. I am impressed with your work and skill. Thanks.

    ReplyDelete
  10. Very good, This information is essential and informative which you have shared here. Read more info about Rain Shower Malaysia. It is beneficial for beginners to develop their knowledge. It is very gainful information. Thanks for share it.

    ReplyDelete

Post a Comment

Popular posts from this blog

Bathroom Remodel - Demolition Part 2

I spent three weekend afternoons to tear down the bathroom and to clean up the debris. It was nice to have an extra day-off (Veterans Day 2018). I was able to work on the project at a comfortable speed. I am getting old and do not perform well when I rush myself. All in all, I took up the do-it-yourself remodeling project to learn new things and enjoy the process for the most part. So the biggest hurdle so far was to remove the near 300 lbs bathtub by myself. I managed to cut the tub into 8 manageable pieces. I was right assuming that it was made of steel, not cast iron or galvanized steel. The cross section of the cut surface showed shiny metal gloss, indicating the bathtub was made of steel. Once the bathtub was cut into eight pieces, it was easy light enough to move it out of the bathroom by myself. I wondered if anyone driving by my house would be interested in scrap metals to make some cash money by recycling. I took the cut pieces of steel bathtub out and left them on the

A great hardwood floor refinish example

The author has finished a really awesome hardwood floor refinish project pretty much all by herself. I am so inspired and motivated by this blog author's success. I have similar problems and plans for my own home's hardwood floor. This blog article gave me some good directions and expectations in realistic sense on what a home owner can do. http://mominmusiccity.com/happens-dont-listen-folks-lowes/